Duerkopp Adler HP Series Additional guide Manual de Instruções descarregar pdf (Página 59)

EFKA AB220A511159

7.2 Operator Level

The preset values of the following list of parameters refer to the setting of parameter 290 = 0.

Parameter Designation Unit max min Preset Ind.

000 c2 - Number of stitches of start backtack forward stitches 254 0 2 *) A

- Number of stitches of start stitch condensing

without stitch regulator

- Number of stitches of end counting “chain

001 c1 - Number of stitches of start backtack backward stitches 254 0 4 *) A

- Number of stitches of start stitch condensing

with stitch regulator

- Number of stitches of start counting “chain

002 c3 - Number of stitches of end backtack backward stitches 254 0 2 *) A

- Number of stitches of end stitch condensing

with stitch regulator

- Number of stitches of tape cutter at the start

of the seam

003 c4 - Number of stitches of end backtack forward stitches 254 0 2 *) A

- Number of stitches of end stitch condensing

without stitch regulator

- Number of stitches of tape cutter at the seam

end

004 LS Light barrier compensating stitches stitches 254 0 7 *) A

005 LSF Number of stitches of the light barrier filter for stitches 254 0 1 A

knitted fabrics

006 LSn Number of light barrier seams 15 1 1 *) A

007 Stc Number of stitches for the seam with stitch stitches 254 0 20 A

counting

008 -F- A parameter from the technician level is assigned to 5 1 1 *) A

the 9 key on the V820 control panel

1 = Softstart On/Off

2 = Ornamental backtack On/Off

3 = Sewing start blocked with light barrier uncovered

On/Off

4 = Unlocking the chain On/Off

5 = Signals A1 and/or A2 On/Off with slide-in strips

1...4 (lefthand arrow = A1, righthand arrow = A2)

009 LS Light barrier On/Off 1 0 0 *) A

013 FA Thread trimmer On/Off 1 0 1 *) A

014 FW Thread wiper On/Off 1 0 1 *) A

015 StS Stitch counting On/Off 1 0 0 A

018 UoS 0 = Sequence “overlock mode with stop” 3 0 0 A

1 = Sequence “overlock mode without automatic

stop. When the command “run” is given, the

drive runs at the preselected speed. With

pedal in pos. 0 or light barrier covered, the

program switches to the next start of a seam

without issuing signals M1/M2.

2 = As with setting “1”. But with pedal in pos. 0

signals M1/M2 will be issued, and the program

switches to the next start of a seam.

3 = As with setting “1”. But with pedal in pos. -2

signals M1/M2 will be issued, and the program

switches to the next start of a seam. Inter-

mediate stop and sewing foot lift with pedal

in pos. –1 are possible.

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 83 84

Comentários a estes Manuais

Sem comentários

Duerkopp Adler HP Series Additional guide Manual de Instruções Página 59

Comentários a estes Manuais

Manuais e produtos relacionados com Máquinas de costura Duerkopp Adler HP Series Additional guide